Select up to 3 products
A general line of adapters supplied with spherical joints to be used in assemblies for distillation, extraction, or your own requirements. On code -30, please specify capacity and catalog number of item into which the adapter is going to be placed. The
Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure.
These PYREX® Claisen adapters have Standard Taper outer joints at the upper end and on the parallel sidearm and an inner Standard Taper joint at the lower end.
Outer joint at angle of 105 degree. Hose connection opposite top joint. Stem below joint, 30mm. The Adapter, Vacuum Take-off, Short Stem is a specialized glass component designed for efficient vacuum take-off in laboratory setups. Its short stem facilitates easy integration with existing glassware...
Manufactured by United Scientific Supplies, this stirring rod is an essential tool for any lab environment. Its glass construction ensures it won't react with the chemicals it comes into contact with, preserving the integrity of your experiments. The rod is also adept at evenly distributing heat...
Hickman Still Head, with Side Port, Synthware, Joint: 14/10, for microscale fractional distillation, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.
Used to regulate the flow of gases or liquids into reaction systems. Stopcock has a bore of 2mm and is supplied complete with a CG-423 retaining clip. Hose connection has an O.D. of 8mm at the middle serration.
Premium quality stainless steel KF/NW25 3-way tee flange for secure vacuum connection. Now you can hook up multiply vacuum ovens to one pump, or multiply pumps to one oven to draw a faster and deeper vacuum. Compatible with the following products from Across International: Vacuum ovens with KF/NW25...
Unique design of bubbler allows for fine control of purge gas within an inert gas system such as a manifold. Purge gas enters bubbler through hose connection (A) and exits thru connection (B) which is connected to manifold. The large capacity of the main chamber (C) allows for rapid purging with...
For use as distillation column packing, mixing beads, and boiling stones. Each 454 g box has a packing volume of approx. 360 cm3. +/-10% variation in bead size.
For use with gas inlet tubes or plain stem thermometers. Supplied with one holed rubber adapter.
One Pound Plastic Jars Chemical Resistant Glass Balls
Stopcock available with glass or PTFE plug For regulating the flow of gases or liquids into reaction systems. Adapter consists of male standard taper joint fittng with stopcock and a 90° angle male hose barb. Thomas numbers 5738D01, D03, D15, and D17 take 1/4" i.d. flex tubing; Thomas numbers...
Adapter has a #7 Chem-Thread at the top for vacuum tight seal of plain stem thermometers. With the same size inner joints on the bottom and sidearm at a 75º angle to one another. Supplied complete with a compression cap and Viton o-ring. FOR THERMOMETERS SEE CG-3503.
Porous discs for use in fabrication of special glass apparatus. Available in F, M, C and XC porosities. Pressure Limits: Fritted glassware is designed for low pressure vacuum filtration or gas flow. The MAX differential pressure should not exceed 15 PSI. Thermal Limits: Fritted glassware should not...
With Vigreux Indentations, used with 25mm immersion thermometer, and D27 distillation receiver. The SYNTHWARE Microscale Vigreux Distilling Heads are designed for precise distillation in microscale experiments. Their design incorporates multiple indentations to enhance separation efficiency during...
Ring-style hose connections for use with regular size condensers, etc. Codes -03 & -07 are on straight tubing; code -11 has a flare end. Sold in shelf-packs of 12 each.
Hollow fritted cylinder at the end of an 8mm O.D. tube. Cylinder is approximately 12mm O.D. x 20mm long. Overall length is approximately 10 inches.
Adapter is used to connect distilling column with vertical condensers. With standard taper outer joint at the top for use with 10/18 or 10/30 jointed thermometers. Both lower inner joints are the same size. Side arm is at a 75º angle to the vertical tube. For thermometers see CG-3506-N.
These PYREX® angle connecting adapters have a sidearm at an approximately 75° angle from the lower joint. The lower end and sidearm are equipped with inner 14/20 Standard Taper joints, and the upper end with an outer 14/20 Standard Taper joint. This tube is also a replacement part for...
Synthware distillation adapter with Kjeldahl trap. With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is approximately 200mm.
This PYREX® tube is approximately 200mm long and may be used for simple semi-micro vacuum or atmospheric distillation, either as a reaction flask or a receiving tube. It has two 24/40 Standard Taper outer joints. This tube is also a replacement part for organic chemistry kit No. 6949 (Thomas No....
Crafted with precision by Kemtech America, this SYNTHWARE Adapter is designed to connect laboratory glassware with a #15 O-ring joint to a 10mm hose. Facilitating efficient and secure connections in your laboratory setup, this adapter is paramount for conducting a wide range of scientific...
For the introduction of gases or liquids during reactions. Bleed tube is 7mm OD X 265mm overall length with a tapered delivery end and capillary tip.