Chemglass

Coil style reflux condenser with a larger diameter jacket and coil, thereby providing maximum cooling capacity, while being shorter in length. Hose connections are on the bottom of the condenser which makes it easier to connect hose/tubing. Connections are GL14 polypropylene hose barbs and screw...

Class "A" micro volumetric flask calibrated to contain. Flask has a GPI 13-425 top thread and is supplied complete with an open top screw cap and PTFE faced silicone septa. Flasks have hex base for stability and ;V shaped interior bottom for total sample retrieval. See MW-102 for...

These caps, made of polypropylene, are ideal for use with volatile solvents, sensitive compounds, and biological media. The SURE-LINK process welds each cap with a Polypropylene/PTFE/Silicone liner bonded to the cap. This process allows the cap to maintain seal through multiple autoclaving...

Three twist-off seals permit easy conversion from a solid to a one, two, or three-hole stopper. Soft, resilient, natural rubber demonstrates exceptional aging characteristics and withstands repeated autoclaving. Autoclavable at 250°F for 30 minutes under water or steam conditions only (not...

Neoprene filter adapters are designed to fit between a filtering funnel and a flask. For use with Buchner funnels, Gooch crucibles, filter tubes, etc. Can be used individually or nested with adjacent sizes. Eliminates the boring of rubber stoppers and the difficulties of inserting and removing glass...

Hemple style distilling column, vacuum jacketed to improve performance. Indentations on the inner tube support the packing material. All sizes have an I.D. of approximately 10mm.

These convenience packs come with 100 bonded closures and vials packed seperately. Closures with bonded septa are not attached.

These vials are manufactured from Type 1 Class A borosilicate glass. The radius bottom vials can be used on LEAP Technologies Inc, CTC Analytics, Varian, Gerstel and other instruments using CombiPAL and other models requiring magnetic capable closures.

Condenser for use in cooling of the scrubbing fluid. Graham coil type condenser having 1/2" Swagelok® tubing for use with CG-1975-20 compression fitting. Overall length is ~350mm with effective length of 250mm. Hose connections have 9mm OD small serration and a 10mm OD large serration.

Sleeve type stoppers with a hollow plugs and sleeve extensions that folds down over the neck of a vessel, tubing, etc. The diaphragm can be punctured with a syringe needle, re-sealing after the needle is withdrawn. Available in either RED or WHITE rubber.

Flask has a funnel top with a standard taper outer grind to accept a 24/40 long neck stopper allowing the handle to extend above the liquid seal. Used in ASTM D29 and ASTM D555. Available complete with stopper or flask only.

Unique one-piece distilling condenser is actually a 75° adapter, highly efficient coil condenser and vacuum adapter in a compact one-piece unit. Available with a choice of three sizes of condensers with uptake inner joint as listed. Top thermometer joint is a 10/30 outer for use with a 3in...

Similar to CG-1947, support clamp is designed to fit just below the flange of all Chemglass Reactors and permits Reactor lid to be detached without removing the Reactor body from the support clamp. Improved clamp is hinged on one side to swing open and allow complete access to install/remove reactor...

Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection has an O.D. of 10mm at the largest serration.

These convenience kits come with 100 vials with the closures attached. Packaged in convenient vial trays.

For performing quick separations using a vacuum source. All funnels have a lower standard taper inner joint with a sealed in drip tip and an outlet for connection to a vacuum source. All sizes have a Coarse porosity fritted disc.

Adapter has a 0-4mm Chem-Vac™ Chem-Cap® valve between the top outer and lower inner joints, both of which are the same size. Available in two configurations: Style "A" having the valve mounted in-line, while Style "B" has the valve 90º to the joints with a brace...

Heavy duty epoxy coated alloy clamp has high tensile strength and corrosion resistance. Can be used to support stirrers, temperature monitors and condensers. Large hand knobs allow easy adjusment and secure clamping power. Useful wherever clamping at 90° is required.

Adapter has a 10/30 outer joint at the top for use with CG-3506 thermometers. When used with vertical side neck flasks, thermometers can be angled into the bottom of the flask. FOR THERMOMETERS SEE CG-3506-N.

"U" shaped drying tube supplied complete with rubber stopper, glass inlet tube, and a lower inner joint.

Bushing style adapter having a lower standard taper inner joint and outer joint ground in the bore of the adapter. Adapters having a 10/18 or 10/30 outer member in the bore are used to insert thermometers into apparatus.

Flow control adapter for use with CG-1188 and CG-1189 chromatography columns along with CG-1190 reservoirs. Adapter has a 0-4mm Chem-Cap® metering plug.

These convenience packs come with 100 bonded closures and vials packed seperately. Closures with bonded septa are not attached.

Rings are made of borosilicate glass and sold in one pound packages. 1lb of 6x6 rings is approx. 2304pcs which is roughly 391cm³ 1lb of 8x8 rings is approx. 1150pcs which is roughly 462cm³