Select up to 3 products
These convenience packs come with 100 bonded closures and vials packed seperately. Closures with bonded septa are not attached.
Strain relief molded into stopper at tubing exit areas to prevent kinking Manufactured, assembled and packaged in Class 7 cleanroom USP Class VI approved materials Animal Derived Component Free (ADCF) Gamma irradiated at 25kGY-40kGY Strain relief molded into stopper at tubing exit areas to prevent...
Dispenser and labeling tape kits include one multi-roll tape dispenser and 14 rolls of tape; 2 rolls of each color (white, yellow, green, red, orange, blue and lavender), either 3/4 or 1 inch wide.
Buchner style filter funnel having a lower standard taper inner joint and serrated tubulation for connection to a vacuum source. Disc diameters and height above the disc are the same as CG-1402.
Cap is made from PBT (thermoplastic polyester) and will withstand temperatures from -45 to 200°C. PTFE seal is also available separately.
Heavy wall pressure vessels have an internal thread for use with PTFE bushings as pressure seals. The unique design allows hand tightening and loosing for easy access into the vessel. O-ring is positioned on the bushing above the thread for improved sealing. Vessels are useful for pressure reactions...
NORELL™ Standard Series™ NMR Tubes are manufactured out of ASTM Type 1 Class B glass, commonly referred to as N-51A. Applications that are suited for using this type of glass are routine NMR, where samples are run under room temperatures with no thermal gradients, for auto-sampling...
Adapters are used for reduced pressure filtration with plain stem buchner funnels. Top is tooled to accept the listed size of pluro-stopper. Serrated hose connection has an O.D. of 10mm at the largest serration. FOR PLURO STOPPERS SEE CG-1401.
10mm O.D. shaft is constructed using a molding process whereas the blade is molded directly onto the PTFE coated stainless steel shaft. This makes the stirrer chemically inert, easy to clean and can be used up to 280°C. The top of the shaft has 50mm of exposed 1/4" diameter stainless steel...
Round bottom storage flask with a standard taper outer joint on the sidearm. The 50, 100 and 250mL sizes have a 0-4mm Chem-Vac™ Chem-Cap® valve while the 500 and 1000mL sizes have a 0-8mm valve size.
Used for microscale recrystallizing of small quantities of reaction product. Consists of a glass outer tube with a non-uniform grind to purposely allow leakage, and a PTFE inner plug. The PTFE inner plug fits both the 1.0ml and 2.0ml capacity outer tubes. Capacity listed is the volume of the tube...
The unique design of our Tru-Stir™ stirrer shaft coupling eliminates the need to use rubber hose or universal adapters to attach your stirrer shafts to overhead stir motors. Coupling incorporates a unique helical stainless steel spring permitting up to 1/4” of offset misalignment and...
2800mL flask with 3 baffles on the bottom surface of the flask to help oxygen transfer to the culture medium.
Heavy duty, molded TLC developing tank for use with plates up to 20 x 20 cm (8in x 8in). The weight of the tank is approximately 15 pounds and the bottom is ground to insure stability. The unique latching system holds the matching ground surfaces of the lid and tank firmly in place, enhancing the...
Open top cap for use with GL screw threads. The cap combined with the CG-197 sealing ring will accommodate tubing of the listed diameter. Cap is made from PBT (thermoplastic polyester) and will withstand temperatures from -45 to 200°C.
Adapter has an outer luer joint that provides a convenient way to connect solid phase extraction (SPE) cartridges, tubes or syringes to a standard taper inner joint. The adapter provides for easier sample concentration and clean-up while reducing the chances of cross-contamination. The addition of a...
Storage vessel sidearm has a 9mm OD tubulation for use with 3/8" Cajon® connections. Chem-Vac™ Chem-Cap® valve is used to control gas or liquid flow into the vessel.
Low actinic red stained glass provides protection to light sensitive solutions. Allowing less than 1% transmission below 400nm and 5% from 400-600nm. Wide mouth design facilitates mixing, pipette access, sampling and filling. Unique Flat Bottom Interior permits the use of a standard stir bar. Large...
Enhance your laboratory's sample storage and observation with Chemglass's Clear Complete Storage Vials. As part of their extensive vial collection, these transparent units facilitate easy visual inspection of stored materials, ensuring sample integrity and easy identification. Their clear glass...
Flask has 3 baffles on the lower outside edge of the flask to maximize oxygen transfer to the culture medium when used on an orbital shaker. The polypropylene vented caps have a 0.22µm (PTFE) hydrophobic membrane to allow sterile gas exchange while preventing contamination. Since these caps...
Unique 5L Rotary Evaporator design fills the opening between benchtop and industrial evaporators systems. Features a large bath for a 5L flask. Continuous reflux with a 3L receiving flask and a reflux valve and a bottom drain valve for the receiving flask. Motorized lift with push button control....
Reaction vessel lid is constructed entirely of PTFE. Low-form lid has nine openings: (A) center neck 1"; female NPT for PTFE standard taper adapter, (B) side necks 1"; female NPT, vertical for PTFE standard taper adapters, (C) side neck 1"; female NPT with 10° X 10° compound...
Chemistry filter adapter is used for reduced pressure filtration with plain stem buchner funnels. Top has a HEAVY DUTY tooled flare to accept the listed size pluro stopper. Hose connection is 10mm OD at the largest serration. ADAPTER IS NOT SUPPLIED WITH RUBBER PLURO STOPPER. CG-1052-A-14 Accepts up...
Solid ring with built in clamp for attachment directly to support rod. Available in three sizes. Nickel plated zinc alloy.