GC Equipment & Instruments

Seats ferrule* onto column for consistent installations Prevents crushed column ends Made from high-quality stainless steel *For use with graphite ferrules only.

Removes up to 600 mg of oxygen or 2 g of water Long life—typically purifies more than five 200 ft 3 cylinders Reduces oxygen to 15 ppb Maximum operating pressure: 250 psi (1,724 kPa) Flow: 3 L/min @ 32 psi (221 kPa)

This kit contains the tubing and fittings needed to add an additional GC to your lab bench. Kit includes: tubing cutter, one 1/8-inch x 1/4-inch reamer, one 1/4-inch x 1/8-inch brass tube end reducer, one 7/16-inch wrench, one 1/2-inch wrench, four 1/8-inch brass tees, ten 1/8-inch brass nuts, ten...

Agilent Technologies products are intended for sale/shipment within the US only. International customers should contact their local Agilent Technologies distributor to place orders for Agilent Technologies products.

Purged with ultra-high-purity helium; ready to use with any carrier gas including hydrogen Reduces water to less than 15 ppb Maximum operating pressure: 250 psi (1,724 kPa) Maximum flow: 1.25 L/min

Stainless Steel Sample Port Assembly 3/8" For 7L Bioreactor Specifications: Material: 316L Stainless Steel w/ Electropolish Finish Tubing: .250" x .152" Overall Length: 1415/16" Insertion Length: 12 7/8" Includes: Stainless Steel 3/8-24 Nut & O-Ring

Hellma® fluorescence cuvettes, standard cells, Macro with PTFE stoppers (spectral range 200-2,500 nm, pathlength 10x10 mm, chamber volume 3,500 muL) are available in high-performance Suprasil quartz material. The highest level of sensitivity in the measurement can be achieved by suitably selecting...

These high-purity, single-stage, single-gauge regulators have a 316 SS diaphragm for accurate, stable pressure control of Aldrich liquefied gases. Delivery pressure: 1-50 psi, 1/4 in. NPTF inlet, hose barb outlet. Legal Information: Aldrich is a registered trademark of Sigma-Aldrich Co. LLC Other...

Thin-wall FEP liner minimizes filling factor losses of using inserts and protects NMR tube from etching effects of strong acids containing fluoride ions. Liners are 8 in. L and fit snugly into most common 7 in. L thin-wall tubes. A PTFE plug to close each liner is included. Not recommended for...

Used to generate a localized cold surface on the exterior of the finger. Commonly used for sublimation, and can also be used in re-flux or distillation operations.

Supplies for 255 Nitrogen Chemiluminescence Detector (NCD). This nitrogen-specific detector is based on a chemiluminescent reaction; complex sample matrices can be analyzed. Agilent Technologies products are intended for sale/shipment within the US only. International customers should contact their...

Offering unrivaled performance in gas chromatography, the GRAPHPACK 2M Ferrules from Restek are specifically designed for Gerstel CIS 3 and CIS 4 PTV Inlets. Manufactured to the highest quality standards, these ferrules ensure a leak-free seal, contributing to consistent and reliable results. Their...

Ideal for use with Over Head Drive Vessels. Manufactured from 316L electropolished stainless steel with 32RA finish or better. Specifications: 1-Siphon Tube 15 5/8" Long 1-Fill Tube 2 17/64" Long 1-Vent Tube 1" Long Material: 316l Stainless Steel Includes: 45mm Screw Cap & White Silicone Liner.

Consistently make precise, clean, square cuts with a diamond blade Built-in magnifier to verify square cut Use with 0.25 mm ID to 0.53 mm ID tubing (0.78 mm OD maximum)

A polycarbonate/acetal copolymer on-off control with female Luer-Lock inlet and male Luer-Lock outlet ports.

316 L Stainless Steel Pitched Blade Impeller, 3L Specifications: Material: 316L Stainless Steel with Electropolish Finish Dimensions: 1 3/4" For 5/16" Shafts Usually Requires 2 Each

with PTFE stopper, black side walls and base Legal Information: Suprasil is a registered trademark of HERAEUS QUARZGLAS GMBH & CO.

Legal Information: T3P is a registered trademark of Archimica GmbH

General purpose single bank vacuum manifold with 3, 4, or 5 ports. Main tube is 38mm OD with a serrated hose connection, having the smallest serration 13.5mm and the largest serration 15.5mm, located at either the left or right side for vacuum connection. Ports are either 0-4mm or 0-8mm...

Stainless Steel Pitch Blade Impeller 7L Specifications: 316L Stainless Steel Ra 32 Finish or Better

Precision, all-glass construction virtually eliminates sidebands. Superior to PTFE inserts in variable-temperature experiments. Upper section of insert fits snugly into the outer NMR tube; 2 mm O.D. insert stem is held straight within 0.013 mm. Use inserts with 5 mm O.D. x 7 in. L thin-wall NMR...

Made of Pyrex® borosilicate glass for compatibility with ground joints, valves, and vacuum racks. Precision ground and highly polished for spinning stability and highest resolution. Tubes have round bottoms and include a sandblasted marking spot for labeling samples. Tubes are thin-walled. Tubes...

Removes burrs from stainless steel tubing For 1/4- or 1/8-inch tubing Nonslip safety design

The Agilent 355 Sulfur Chemiluminescence Detector (SCD) is the most sensitive and selective chromatographic sulfur detector available for the analysis of sulfur compounds. This product is only available to U.S. Domestic Customers. Agilent Technologies products are intended for sale/shipment within...