Shaft Stirrers

•Guaranteed chemically resistant, inert and leak-free •Use up to 280C (540F) •Encapsulated stainless steel core for maximum rigidityPlease note: The propeller and shaft are fused together.

Fully flexible drive shaft facilitates isolation of the stirrer motor from the reactor. Complete units, code -30 (91.4cm) and code -32 (152.4cm), designed for use with 8mm (5/16in) motor shaft. Purchase the optional code -27 adapter for motors with 9.5mm (3/8in) shafts. Reactor end consists of a...

Thomas No. 1198F83: Stirring shaft with floating blades: The two blades that open as the speed rises generate an axial flow in the container, from the top towards the bottom. Particularly recommended for stirring in narrow-neck containers, e.g. flasks. Thomas No. 1198F84: Stirring shaft with folding...

Chlorofluorocarbon grease for use at speeds up to 6000 r.p.m. with ACE standard glass assemblies. Use 8040 water-cooled type bearing for long-time stirring (over one hour). Below one hour, 8038 type may be used at 1500 r.p.m.; eight hours at 1000 r.p.m. High chemical inertness unaffected by strong...

Blade is shaped to resemble the contour of a round bottom flask. Blades are available solid or perforated. Made of 3/16" PTFE to fit 19mm OD stirrer shafts. Minimum joint size listed is the size required to allow passage of the blade.

Precision ground glass stirring shafts, 10mm OD, paddled, button type and bead type. Button type shafts accept 8083, 8085, 8086, 8087 & 8096 stir blades. Beaded shafts accept 8088, 8089, 8090 & 8091 agitators. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 & 8055. Use...

Uniquely designed and lubricant free, these precision stirrer/stirring bearings are self-aligning. The saddle O-ring provides constant force and a positive seal on the stirring rod that allows vacuum operation to as low as 1mm. Ground finish rods from other manufacturers are not recommended for use...

Thomas No. 1177M38 Impeller. Mixer. Blade. Crossed Blade. Radial Flow. High Speed. Low Viscosity. 316L SS. Electropolished. High Shear. High Vortexing. Thomas No. 1177M39 This radial flow impeller is effective for high speed, low viscosity mixing. The 50 mm (2”) diameter blade is...

Support Stand was designed to accommodate vessels up to 10" diameter, to sit close to the support rod. Support rod is ideal for mounting stirring motors. Each of the four corners rests on a rubber cushion. The powder coated steel base measures 7.875” (200mm) W x 12.5" (316mm) deep...

Agitators are made entirely of PTFE and glass filled PTFE and are for use with 10mm OD stirrer shaft CG-2075-B. Available in 45°, 60° and 90° impeller angles. The 45° and 60° impellers are set up to stir downwards in a clockwise direction and upwards when rotated...

316 stainless steel, football shaped, stir blades for 10mm OD button type stir shafts. Holed versions, codes -70 thru -74, provide even greater agitation. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.

The small mixing shaft and head of the Jiffy Mixer is specially designed to stir viscous solutions (like food toppings, lotions, cell paste, epoxy resins, paint - anything that is 'flowable'). It thoroughly disperses and/or dissolves multi-part mixtures or suspensions of powders. Where ordinary...

Heavy duty PTFE anchor made of 0.500” thick PTFE. Blade is shaped to mirror the contour of Chemglass cylindrical reactors. Designed for use with CG-2078 Chem-Stir® 10mm stirrer shaft. The blade is secured to the stirrer via a PTFE pin.  PLEASE NOTE: CG-2081-A-02 IS NOT RECOMMENDED FOR...

Nylon chuck for use with ACE stirring shafts or other shafts of the same dimensions. Chuck has flexible insert which allows for misalignment of shaft without danger of breakage.

A 10mm OD precision ground and polished stirrer shaft with our patented** Chem-Stir™ blade attachment system. Shaft (C) has been manufactured with a ring at the lower end to permit attachment of the blade (B) with a PTFE nut (D) and bolt (A). Shaft is supplied complete with PTFE nut and bolt...

Glass bearing design for use with Ace-Thred pressure reactors and our 8075 glass, polished or 8074 bare, stainless steel 10mm stirring shafts. Both the top bushing and bottom coupling are PTFE. Maximum operating speed is 600 rpm.

Ultra-Vacuum stirrer bearing for applications up to 0.6 Torr. Non-shedding bearing is manufactured from PTFE, Rulon and PEEK materials. Equally good in both vacuum and pressure applications as low as 0.6 Torr. Rated for up to 400 rpm with both glass (polished rather than precision ground is best)...

Polished glass stirring shafts, 19mm OD. Available in solid and hollow styles and in various lengths. Join 8085 blades to button type shafts, Join 8091,8092,8093 and 8100 agitators to either knob or drilled style shafts. Join all shafts to stirrer motor using 8124 series chucks. Recommended for use...

Precision Trubore Stirrer Assembly consisting of 10 mm ID bearing, bushing, precision ground, button type glass shaft and blade. Available with either glass or PTFE stir blade.

Precision ground, hollow, 5mm glass stirring shaft. Button type shaft accepts 9542 blades and can be used in matching 9524 and 9527 bearings. Holes are provided in the side of the shaft for material introduction and at the bottom for emission into the flask contents. Join to stirrer motor using 8124...

A 10mm precision ground stirrer shaft to fit CG-2070 through CG-2072 10mm bearings. Side button for attachment of CG-2080 or CG-2081 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF PTFE BEARING.  FOR POLISHED SHAFTS USED WITH PTFE BEARINGS SEE CG-2079.

PTFE oval stir blades for 10mm OD button type stir shafts. 10mm OD shafts can be found in our 8068, 8070, 8074 and 8075 series.

PTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.

Grease-Free PTFE stirrer bearing for use under moderate vacuum. The bearing consists of a PTFE standard taper body, Nylon compression cap, PTFE Insert/bushing and a Nylon loosening nut. The PTFE insert/bushing provides only glass and PTFE contact with the reaction. Loosening nut above the standard...