Ace Glass

Bump trap for use between a rotary evaporator's steam tube and evaporator flask, preventing fluid from being drawn into the condenser. Improved design incorporates two drain holes to expedite the return of solvent to the evaporator flask.

Straight connecting adapter with standard taper inner joints at both ends. Various lengths. Ace Glass provides straight connecting adapters with inner joints, ideal for laboratory glassware setups. These adapters facilitate the connection of various glass components, ensuring a secure fit. Made from...

Schwartz drying tube with standard taper stoppers. The Ace Glass Schwartz Drying Tubes offer a reliable solution for drying gases in laboratory experiments. These tubes are constructed from high-quality glass, providing excellent resistance to thermal shock. Their design ensures efficient removal of...

Precision grade with T-Bore hollow or solid plug.

Glass aseptic filling bell for filling of other glass vessels. Tubing is attached to the top hose connection and the bell is placed over the top of the receiving flask or bottle. See part number 3906 for media dispensing flask.

Precision ground glass stirring shafts, 10mm OD, button type, PTFE coating permits higher stirring speeds with Trubore bearings. If used unlubricated, 500 rpm max with water-cooled 8040 bearing. Compatible with 8036, 8038, 8039, 8043, 8047, 8051, 8055 and 13443 bearings. Button type shafts accept...

Bump trap for use between the rotary evaporator's steam tube and evaporator flask, preventing fluid from being drawn into the condenser.

Mounting bracket permits easy and convenient mounting of 12080 or 12081 Powerstats on standard laboratory racks or stands having up to 16mm O.D. rods. Made of strong, rust and corrosion resistant aluminum alloys. Bracket is attached to the bottom of the powerstat by two screws and to the rack or...

Gas dispersion tube with porous fritted tip for use with #7 Ace-Threds. Tube is bent 15 degree to allow positioning inside flask to avoid stirring paddles and yet reach close to bottom of flask. Specify porosity and length or code when ordering.

These heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.

Identical to 7531-10 with the exception that the nozzle is replaced by a sintered glass filter, porosity A (145-175 microns). Used in determination of Acrolein: 4-Hexylresorcinol Method #1. Bottle has encircling graduations from 0 to 25mL or 0 to 30mL in 5mL divisions. Inlet/ outlet are 7mm O.D. For...

Connecting, reducing adapter with top female joint being smaller than the bottom male joint. The Ace Glass Adapter, Reducing, offers a reliable solution for connecting glassware with differing joint sizes. This adapter is crafted from high-quality glass to ensure a secure fit and seal during...

With spiral condensing tube having both inlet and outlet connections at top, on same side. With standard taper joints. Length between joints is approximately 80-90 mm longer than the stated coil length.

Rugged columns with internally threaded ends to which a wide choice of upper and lower end pieces can be fitted using 5837, 5838, 5841, 5842, and 5843 fittings. Available in a variety of lengths and diameters. Some sizes available with epoxy coating for added protection against scratches.

Two neck, one center and one angled side neck, round bottom flask with standard taper joints. Available in standard wall or heavy wall.

Glass cloning cylinder for cloning or isolating individual cells. Place cylinder into bottom of flask or Petri dish to isolate individual or small group of cells. Disinfectant chambers to be used as described in the 1992 J.A.O.A.C. Hard Surface Carrier Test.

Polished stainless steel stirring shafts, 10mm OD, drilled type with removable button. When used with 8066 PTFE bearing, a lubricant-free vacuum seal can be realized at speeds up to 200 rpm. Recommended for use with 8044,8050,8066,13443 and 13445 bearings. With button, shaft accepts...

Vacuum jacketed and silvered with viewing strip or unsilvered. For use with No. 7792 Head. With standard taper 24/40 joints. Effective length, 250mm.

Septa tops are flanged with a sleeve-like extension that folds down over the vessel's neck. Punctured diaphragm re-seals after syringe is withdrawn. Septa are supplied in a variety of sizes, red, white or grey rubber.

O-Rings in a variety of sizes and materials. Please see o-ring materials chemical compatibility here: http://www.aceglass.com/downloads/eccc.pdf

Fabricated from Borosilicate glass. Wall weight on 5mm size is approximately 0.8, other sizes have wall weight of approximately 1.0/mm.

Rugged, heavy wall head for use with 6384, 6386, 6388, 6423, 6425, 6427, or 6429 reaction flasks. Duran flange supplied with a shallow O-Ring groove for use with mating grooved flask. #15 Ace-Thred center and various #15 and #7 side necks available allow connections under pressure conditions without...

Replacement drying flask for Buchi rotary evaporators. Pear shaped heavy wall with a standard taper single neck. Available plain or safety coated.

Borosilicate glass transition adapter to convert beaded pipe 2 to standard taper joint. The Beaded Pipe to Standard Taper Joint Adapter by Ace Glass is engineered for seamless integration of beaded pipes with standard taper joints. Its precision design ensures a snug fit, reducing the potential for...