Chemglass
-
MicroCarrier spinner flasks promote optimal growth of suspension and microcarrier cultures. Indented bottom (100mL thru 1000mL) prevents accumulation of microcarrier beads under the impeller paddle. The 3L version does not have a dimple. The complete system includes a flask with two angled sidearms…
-
Clamps
ChemglassCLAMPS, BURET, Clamp will hold two burets from micro to 100mL. Spring loaded mechanism adjusts simply by squeezing, yet hold buret firmly in place. Mounts directly to standard support rod with built in hook connector. Constructed of epoxy coated aluminum with vinyl jaws. CHEMGLASS LAB CLAMPS,…
-
Button Style 10mm Stirring Shaft
ChemglassA 10mm precision ground stirrer shaft to fit CG-2070 through CG-2072 10mm bearings. Side button for attachment of CG-2080 or CG-2081 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF PTFE BEARING. FOR POLISHED SHAFTS USED WITH PTFE BEARINGS SEE CG-2079.
-
Adapters, Vacuum Take-Off, 105°
ChemglassWith standard taper top outer and lower inner joints with sealed in drip tip. Adapter is bent at a 105° angle for use in vacuum distillation. Serrated hose connection has an O.D. of 10mm at the largest serration for connection to vacuum source.
-
9mm Certified Bonded Closures
ChemglassCertified Bonded closures feature clear PTFE/Silicone bonded directly to the closure without the use of glue or adhesives. These bonded closures provide a cost effective, integrated, one-piece system that eliminates costly line fallout. Closures are available in both pre-slit and non-slit designs.
-
Thick Quartz Ground and Polished Plates
ChemglassCommercial quality ground and polished clear fused quartz. Edges have a ground finished on all sizes.
-
Similar to CG-147, but formed without the o-ring groove.
-
Similar to CG-1241 but with the Vigreux column vacuum jacketed to improve distillation performance.
-
Storage vessel sidearm has a 9mm OD tubulation for use with 3/8" Cajon® connections. Chem-Vac™ Chem-Cap® valve is used to control gas or liquid flow into the vessel.
-
General purpose column having a PTFE stopcock, reservoir of the listed capacity and a top standard taper outer joint. Glass wool (not supplied) is used to support the column packing. Column is constructed using MEDIUM WALL TUBING. Can be used as a gravity eluted column or a flash column (as…
-
Pressure Vessel, Heavy Wall
ChemglassHeavy wall pressure vessels have an internal thread for use with PTFE bushings as pressure seals. The unique design allows hand tightening and loosing for easy access into the vessel. O-ring is positioned on the bushing above the thread for improved sealing. Vessels are useful for pressure…
-
Flexible and compact, this 4-port line is constructed using CG-474-02, 4mm double oblique hollow high vacuum greased stopcocks on all four ports. Ports are fitted with two 14/20 inner joints and two 24/40 inner joints and are spaced 5" center to center. This configuration permits use directly…
-
Flowmeters, Bubble
ChemglassUsed for the control of carrier gases. Projection at top breaks bubbles. Supplied complete with rubber bulb. Hose connection has a O.D. of 9mm at the middle ring.
-
Glass Blowers Hose Connections, Micro
ChemglassUsed to construct small scale apparatus. Available in direct sealing or regular style. Serrations are tooled on both ends of an 8in length of tubing. Hose connections are SOLD IN PACKAGES OF 10 SERRATED CONNECTORS (5 pcs. tooled on both ends).
-
Stainless Steel Quick connects terminating in a male M16 thread. Quick connects have fluorosilicone seals. Both male and female couplers have shutoffs. Quick connects provide a easy and convenient way to change out reactor systems or disconnecting hoses. Temperature range is -60 to 200° C. M16…
-
Replacement Threads, G.P.I.
ChemglassThread for replacement on apparatus using G.P.I. (Glass Packaging Institute) thread. These threads are used primarily on products manufactured in the United States. When a thread is designated as 20-400 it means that the diameter across the top of the threaded area is ~20mm. The numerical 400…
-
Round bottom, HEAVY WALL, three-flask with standard taper outer joints on the center and side necks. Entire body of the flask is jacketed and has two hose connections for circulation of heating or cooling liquid. Indentations increase agitation of the contents of the flask during stirring. …
-
OptiTherm® aluminum reaction / heating blocks provide a SAFE and cost effective solution for replacing your existing oil baths and heating mantles. The innovative PTFE shield on the unit reduces the exterior exposed surface temperature by as much as 100°C. For example the PTFE shield would…
-
PTFE 60° Agitators
ChemglassAgitator blades are constructed of PTFE with a glass filled PTFE locking nut. This enables them to be attached to the shaft in any vertical position. Note: Designed for use with CG-2079-X, CG-2078-X or CG-2096-X PTFE Covered stainless steel type shafts
-
Adapter has the listed size of Chem-Thread at the top for a vacuum tight seal of a variety of tubing diameters. Will accept glass, metal or heavy wall plastic tubes having diameters between 7 to 18mm O.D. such as thermometer wells, gas dispersion tubes, plain stem funnels, etc. Serrated hose…
-
Our controllers feature solid-state proportional voltage power control in a compact benchtop design. Controllers provide accurate manual control of heating mantles, tapes and all other resistive loads with an adjustable output range from 5 to 100% of the rated voltage. All units are supplied with a…
-
Reaction Vessel Lids, 5-Necks
ChemglassFive neck vessel lid to fit CG-1920 through CG-1936 vessels. Lid has a flat ground surface allowing it to be greased or used with an o-ring.
-
Beakers are made from 316L stainless steel and available in capacities of 1, 2, 3, and 5 liters. Beakers have solid bar sanitary handle, easy-pouring beaker-spout, and graduation marks. All beakers have a seamless sanitary interior and standard 10 Ra finish. Features: Beakers have solid…
-
Preassembled Clear Vials
ChemglassThese convenience kits come with 100 vials with the closures attached. Packaged in convenient vial trays.
-
Drying Apparatus, Abderhalden
ChemglassAbderhalden style for drying samples at a temperature as a function of the solvent boiling point. The desiccant flask has a 34/45 outer joint for connection to the drying chamber. All other joints are 24/40. Complete apparatus consists of a desiccant flask, drying chamber, round bottom flask and…
-
Single Neck Flat Bottom Flasks
ChemglassSingle neck, flat bottom flask with a standard taper outer joint.
-
Sample Vault™ Series NMR Tubes
ChemglassThe Sample Vault™ Series of NMR tubes with NorLoc™ caps are engineered for the new generation of high-throughput lab automation NMR systems. Designed for use with 96 position carriers that accept either the 103.5mm (4”) or 178mm (7”) with open or closed top caps.…
-
-
Fritted filter funnel has a choice of coarse or medium porosity fritted disc. Lower outlet is a standard taper inner joint and has a CG-961-01 0-4mm Chem-Vac™ Chem-Cap® valve. Top outer joint is the same size as the lower inner joint. Capacity listed is that above the fritted disc.…
-
Gregar Extractor
ChemglassThe Gregar Extractor† is the first major advance in laboratory extractor design in over 100 years. Developed by Joseph Gregar and Ken Anderson of Argonne National Laboratories, this extractor is the only unit on the market that can perform all three common types of extraction. During solid…
-
Reaction Vessel Lids
ChemglassREACTION VESSEL LIDS, 4-NECKS, 50ML, EQUIVALENT TO METTLER EASYMAX, Reaction Vessel Lid, 4-Nk, 50mL, Compatible with Mettler Systems: (1) 14/20 SN, (1) GL-14 SN, (1) 10/18 SN and (1) 10/10 SN; Equivalent to Mettler Easymax® Part # 51161032Mettler Easymax® is a registered trademark of…
![Site Search powered by SLI Systems](http://assets.resultspage.com/logos/sli_logo_2014.png)