The ROTAX 6.8 is suitable for waste treatment plants, waste-water treatment plants and laboratories involved in environmental analyses. An easy to use instrument with a digital display and speed settings ranging from 0 to 30 rpm. Precise and extremely safe, the ROTAX 6.8 offers excellent performance.

For drawing the material to be mixed from above Stirrers generate axial flow in the vessel Minimum danger of injury when contact is made with vessel Minimum shearing forces Used at medium to high speeds Additional stirrers available on special order

Ideal for applications with changing viscosity requirements Use for either high-speed or high-torque mixing Solid-state controller for precise speed control Two motor axles give you two mixers in one! The direct-drive axle provides high-speed, low-viscosity mixing; switch to the…

The Heidolph overhead stirrers of the Hei-TORQUE series are perfectly designed for powerful stirring, in order to achieve best mixing results even for very challenging applications. Hei-TORQUE Value These stirrers are ideal for standard stirring tasks. They are designed to mix and…

Speed range: 60-2000 rpm Stepless speed control Ambient temperature range: 5 to 40°C The RW 20 digital stirrer offers two speed ranges for universal use from 60 to 2000 rpm. Stirrer has a slim ergonomic design, digital display and constant power drive. Push-through agitator…

PTFE covered stainless steel shaft with solid PTFE, 4 blade screw propeller. Blades are pitched 45 degrees. For a better grip by the stir motor chuck, 50mm of stainless is left exposed.

Shaft Stirrers/Blades Unaffected by virtually all chemicals PTFE construction Unbreakable and will not scratch vessels Usable to 260°C Of virgin PTFE, immune to most chemical attacks (except molten alkali metals). Excellent anti-adhesion properties promote thorough…

Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique design is forgiving of slight misalignment of stir motor and shaft. Recommended for use with our 9534 6mm precision ground stir shaft.

Medium Duty, Model HST10 Totally enclosed, 1/17 hp, permanent magnet DC motor Direct-drive, with rpm/torque readout and X-Y output Maximum rpm: 2,500 Torque: 1.5 lbs.-in. (1.73 kg-cm) Direct drive provides 20 to 2,500 rpm and 1.5 lb.-in. torque. Available for 120 or 240 V, 50/60 Hz…

Caframo’s high torque stirrers are designed and engineered specifically to meet the continuous demands of heavy industrial use. The heart of the BDC line is the high performance Brushless Direct Current (BDC) motor. A unique two speed transmission provides incredible amounts of power. Caframo…

Powerful, mechanically controlled laboratory stirrer designed for highly viscous applications for quantities up to 80 l (H2O). It is suitable for intensive mixing for use in laboratories and pilot plants. The stirrer comes equipped with a protection for overheating of the motor by means of…

The ultimate in compact design measuring only two by four inches. The BDC250 offers great capabilities in a small package; used in formulation, R&D, clinical research, education labs, anywhere a magnetic stirrer is used. It fits into small spaces and can be easily transported to other labs or…

The space-saving high performers from IKA MICROSTAR and MINISTAR series have been complemented by additional models. The new and easy-to-use stirrers convince with perfect basic functionalities, as well as with a compact design. Combining high performance with particular excellence, they require…

3/8HP Brushless DC motor for use on pilot plant reactors up ²to 200L. May be used with either the 120V or 240V BLDC ²motor controllers. Supplied with 6ft removable cable and ²mounting hardware.

Material: 316l stainless steel with ra32 finish or better Size: 15l Paddle size: 3" tall x 7 1/2" wide

Digital Laboratory Stirrer Features DC brushless motor considered superior in safety as there are no brushes to cause sparks and no brush replacement required Direct-drive system reduces noise and require low maintenance Achieves high torque enabling stirring of high viscosity…

Caframo’s BDC2002 offers ultimate versatility and maximizes productivity. With the push of a button, the unique Stirlight™ lights up so that solutions can be seen clearly. Included in each purchase: Overhead stirrer motor, chuck, chuck key, support rod, external power supply, grounded…

More power than stirrers ten times its size! Incredible 91in-oz of power yet fits in the palm of your hand! Safety - Low Voltage - Sparkless Sealed motor housing isolates motor from organic vapors Low voltage operation - Sparkless motor runs on 16 volts Convenience - Weighs less than…

Model 8583J10: Produces propeller speeds from approximately 200 to 10,000 rpm Compact and quiet; operates on compressed air at pressures from 30 to 100 psi (210 to 690 kPa) Sturdy, smooth-running motor develops 1/6 hp (120 W) at 80 psi (550 kPa) input Speed is variable by adjustment…

Support Stand Steel base; legs have rubber pads to cut vibration Support rod is made of stainless steel. Height is 29”; available in two models. Jacob's Chuck, Adjustable Fits 3/8 ” (10 mm) diameter motor shafts Keyless Chuck, Nylon-bodied …

Impellers made of stainless steel (8592H39 through H48) or glass-filled propylene (8592H36) Autoclavable 8592H36 Lower Assembly/Shaft and Impeller; shaft length x diameter: 13-1/2" x 3/8"; impeller diameter: 4". 8592H39 Lower Assembly is for use with the Nalgene 30-gallon,…

Measure viscosity and display it, even during product development: the new IKA STARVISC 200-2.5 control torque-measuring stirrer makes it possible. The result can be read in real-time on the display. STARVISC therefore has a broad range of applications. This is particularly helpful during product…

The LH is the ideal solution for medium-high viscosity liquids. The technopolymer structure ensures optimum chemical resistance and enhanced handling, preventing any possible rust and being extremely light. The robust motor ensures years of continuous operation, with no extra costs for…

Stands Extra strong retort stands with H-pattern base for stability and robust support rod. Both versions include bosshead. Heavy duty stand recommended for use with SS30 overhead stirrer.   Paddle Rods Made from high grade stainless steel, there is a choice of five…

The space-saving high performers from IKA MICROSTAR and MINISTAR series have been complemented by additional models. The new and easy-to-use stirrers convince with perfect basic functionalities, as well as with a compact design. Combining high performance with particular excellence, they require…

400640 & 402645: Reusable Spinner Direct Top Drive Motor High torque, low rpm stirrer motor specifically designed to maintain constant low speed for use on top of Corning® Reusable Spinner Flasks. The gearhead stirrer motor delivers 14.5 in-lbs of torque and has a maximum speed of 350…

For connecting inert gas and vacuum sources Stopcock has metering groove cut into the plug to provide fine control of vacuum and inert gases. Distance between stopcocks is 65 mm for 8651N01 and 100 mm for 8651N03. Include patented pressure/vacuum retainers. Dimensions (mm): 8651N01: 230 L x…

PTFE covered stainless steel shaft with a solid PTFE retreat curve agitator. Featuring a retreat angle of 30 degrees and, for a better grip by the stir motor chuck,50mm of exposed stainless.

Motor, AC variable, hazardous duty, 1/2hp,230/460v 60Hz²3 phase, complete with controller, 115v 50/60Hz input, CE and ²cULus rated. Control box cord to motor is 12ft long, control²box cord to electrial source is 24ft long.