Cyclonic spray chamber drain fitting with ETFE capillary tubing - 24 length by 0.030 ID x 0.062 OD.

The MEINHARD concentric glass nebulizer reflects exacting standards in design and manufacturing. Its advantages include simplicity of design and operation, reproducible and self-aligning aerosol, and close fabrication control.

Replacement connector and sample tubing for glass concentric nebulizers with EzyFit sample inlet.

Concentric Plus Nebulizers provide low dead volume and high sensitivity with excellent detection limits and washout. Each Plus nebulizer includes the FitKit+ gas and sample quick connect fittings. The connections are made with highpurity PFA, minimizing the chance of contamination during backflow…

This nebulizer self-aspirates at low-flow rates with any autosampler and provides the same benefits of the PFA MicroFlow nebulizer. The integrated sampling probe is constructed by encapsulating a rigid support material between layers of PFA to provide a chemically-resistant probe that is…

High solids Gem Cones are for samples with high dissolved solids (up to 20%). This cone spray nebulizer allows you to analyze samples with higher solids concentration than is possible with a Cross-Flow nebulizer. Gem Cone nebulizers require an end cap for use with Ryton Scott Spray Chambers. High…

TUBING-PFA 0.5MM ID

The PEEK Ari Mist ® nebulizer provides very low sample flow and is for samples that are particlate free. Operates on stand pressures of 40 - 50 psi. Fits regular spray chambers as a direct replacement for glass concentric nebulizers. Its features an enhanced parallel path design.

Material: Borosilicate glass  High physical reproducibility ~ 1%, TDS tolerance, typically up to 20%, High tolerance to particulates, typically up to 75um, Low RSD's due to highly accurate construction

Eluo Nebulizer Cleaner Particle build-up in a nebulizer capillary and tip causes sample flow to be constricted, thereby reducing nebulizer efficiency andperformance. Previously there was no simple way to effectively clean and unblock nebulizers. Now, blocked nebulizers can be safelyand easily…

Fused Silica Obstruction Removal Kit for ST type Nebulizers. Used to clear blockage from ST type nebulizers. Inc Features and Benefits Pure Grade Standards for AA and ICP-OES Analyzed by ICP-OES Analyzed by Classical Wet Assay 32 trace impurities analyzed by ICP-MS of the final…

F0 Encapsulated micro tubing for microflow rates with the lowest internal volume of any nebulizer. Includes 0. 25 mm i. d. (green marker) 70 cm long micro capillary. Compatible with all MEINHARD Plus nebulizers.

Used to connect capillary tubing (Product Number: 09908265) to Cross-flow nebulizers, and to larger i.d. peristaltic pump tubing.

PFA-200 Microflow Nebulizer, 200 µL/min, with integrated autosampler probe [Ultem support] for ESI SC Autosampler. HF Resistant. Capillary length 150cm. Probe length 175 mm.

The UniFit connector is a convenient drain connector for glass cyclonic spray chambers.

PFA sample capillary 0. 062 o. d. x 0. 020 i. d. in (1. 59mm x 0. 5mm)60cm length. For use with P/N WE024372 connector.

The MicroMist micro-uptake glass concentric nebulizer offers high performance for limited sample volumes. MicroMists with sample uptakes 0.2 – 0.4 mL/min are fitted with a UniFit connector with 1.3 O.D. x 0.50 mm I.D. x 700 mm long sample tubing. MicroMists with sample uptakes 0.05 – 0.1 mL/min are…

Includes all O-Rings used in the Cross-Flow and Cross-Flow II nebulizers.

The MEINHARD concentric glass nebulizers reflect exacting standards in design and manufacturing. They provide excellent sensitivity and precision for aqueous solutions and samples with few dissolved solids (less than 1%). MEINHARD nebulizers for Optima instruments include Standard Nebulizer…

The UniFit sample tube connector is used with U-Series nebulizers.

Agilent Technologies products are intended for sale/shipment within the US only. International customers should contact their local Agilent Technologies distributor to place orders for Agilent Technologies products.

Complete HF-resistant sample introduction system for NexION 300 and 350. All wetted surfaces are PTFE and Sapphire. Provides a chemically inert and clean introduction system. This kit includes: 47 mm PFA Barrel Spray Chamber with Endcap (N8142000) PFA-ST Nebulizer (N8122192) 1.8 mm I.D.…

The MicroMist ™ micro-uptake glass concentric nebulizer offers high performance for limited sample volumes. MicroMists with sample uptakes 0.2 – 0.6 mL/min are fitted with a UniFit connector with 1.3 mm O.D. x 0.50 mm I.D. x 700 mm long sample tubing (N0777513). MicroMists with sample uptakes 0.05…

0. 5 meters of . 044 OD X . 018 ID. Clear Polyethylene Tubing with attached BRC 3 fitting for sample lines.

Ultraclean PFA PTFE nebulizer with exchangeable capillaries to provide flow rates from 100-400 uL/min. For use with autosamplers. Requires union N8122355 to connect to autosampler probe.

One Sample Introduction Line for PFA-ST Nebulizer is included in the NexION 2000 ICP-MS Productivity Configuration's Consumable Kit (N8150056) and the Semi Configuration's Consumable Kit (N8150057).

Contains a PPS (carbon-filled polyphenyl sulfide) end cap with a Gem Tip clear sapphire sample tip and a Gem Tip red ruby argon tip.

CTFE Liquid fitting - female with barb end

The DuraMist concentric nebulizer is an economical nebulizer for high precision analyses involving samples digested in HF. The DuraMist nebulizer is recommended for samples containing up to 5% HF. For samples with higher concentrations of HF, the OpalMist PFA nebulizer is recommended.

Material: Borosilicate glass High physical reproducibility ~ 1% TDS tolerance, typically ~ 1% High tolerance to particulates, typically up to 150um Low RSD's due to highly accurate construction Slurry nebulizers have a natural liquid uptake of 4mL/min but operate best between 1.5 - 2.5mL/min

OpalMist Nebulizer 0.05mL/min

The UniFit sample tube connector is used with U-Series nebulizers.