LiquiMobil flow indicator made of SAN is mainly suitable for cooling systems and helps to reduce water consumption considerably because the cooling water flow can be adjusted better. Not suitable for aggressive substances. Flow indicators give precise visual indication of the flow velocity of…

Instant visualization of flow in a tubing line Brightly colored indicator polypropylene paddle wheel Fits tubing I.D.: 4mm to 7mm (1/4" to 5/16") Tube ends: Barbed The flow indicator provides immediate visual indication of water, air or gas flow, when the paddle wheel…

A device for the visual indication of liquid flow. Flow indication is visible at a distance. Usable with water down to a flow range of approximately 100 mL/minute, which is adequate for even the smallest cold finger condensers. The upper flow limit is in excess of 1 liter/minute. Speed of ball…

Made of borosilicate glass, these soap film bubble flowmeters are used in routine analytical laboratory gas chromatography to measure flow rate of the carrier gas. A soap bubble, formed in the bottom of the graduated tube, is pushed upward by gas from exit end of the chromatograph. Flow rate is…

CheMobil made of PMP/TPX can be used for many substances due to its good chemical resistance. Not suitable for strong acids, alkalis and solvents. CheMobil can be steam sterilised. Flow indicators give precise visual indication of the flow velocity of liquids or gases being transported through…

Flow Indicator (5084A04) Clear polystyrene Provides immediate visual indication of water, air or gas flow, indicating continuity and relative flow rate Minimum flow rate to actuate the ball with water is 50 mL/min. in horizontal position, 140 mL/min. in vertical position. With…

Used for the control of carrier gases. Projection at top breaks bubbles. Supplied complete with rubber bulb. Hose connection has a O.D. of 9mm at the middle ring.

Precision machined clear acrylic Nitrogen flowmeter with Brass metering valve is for use with Chemglass process reactors. Front of flowmeter has a blue scale indicating the L/min of air. HDPE hose connection is for use with 5/16"; ID tubing. Unit is supplied complete with a 1/2" OD…

Can measure flow rates down to 0.3 ft/sec NIST certified ±0.5% repeatability over full range For use in powered flow systems Flow measuring range of 0.3 to 20 ft/sec Ideal for measuring flow in piping systems with extremely low velocities. Combines the “Hall…

Used for flow measurements in the lab, process flows in pilot plants, metering carrier gases in chromato graphy, indicating and controlling gases in manufacturing processes and for indicating flow rates in pumping or flow systems. Formed from heavy-walled, shock-resistant borosilicate glass, these…

Used for flow measurements in the lab, process flows in pilot plants, metering carrier gases in chromato graphy, indicating and controlling gases in manufacturing processes and for indicating flow rates in pumping or flow systems. Formed from heavy-walled, shock-resistant borosilicate glass, these…

Adaptable to virtually any flow measuring application Flow rate and total displayed Frequency output for remote instruments CE certified for intrinsic safety Measures from 0.3 to 20 ft/sec with an accuracy of ±0.1% of reading. Totalizes flow to an accuracy of…

Flow Indicator (1211Y76) Product Dimensions (l x w x h) : 3.531x0.616x1.605in Paddlewheel. This polystyrene, bright  red paddlewheel indicates liquid or gas flow from  5 ml/sec to 95 ml/sec. The clear outer case allows  for unobstructed view of the wheel which spins freely…

Adjustable nitrogen gas flow meter for Organomation N-EVAP Evaporators. 1/4 inch quick disconnect fitting in 1/4 inch swagelok fitting out

No power required for use Rotor is constructed of PVDF ±0.5% repeatability over full range FM Approved Flow measuring range of 1 to 20 ft/sec NIST certified Rotor-X Flow Sensor Makes creating a flow monitoring/ controlling system easy. Just match it with either…

All fittings are slip-on tee style except for Thomas numbers 5075C55 to C59 which are weldolet weld on style.

Class "A" micro volumetric flask calibrated to contain. Flask has a GPI 13-425 top thread and is supplied complete with an open top screw cap and PTFE faced silicone septa. Flasks have hex base for stability and ;V shaped interior bottom for total sample retrieval. See MW-102 for…

The FM110 Flow Monitor has been carefully designed to provide increased safety in the laboratory by monitoring aqueous liquids used in heating and cooling applications and process control. The turbine assembly is comprised of components made from chemically resistant materials such as PVDF,…