Available with 200 or 300 mm long heavy-wall outer jackets PYREX® West condensers are designed with a heavy-wall outer jacket to provide a sturdy, long-lasting unit, while the inner tube has a thinner wall for efficient heat transfer. The tubulations are on the same side to reduce breakage.…

With molded spiral condensing surface and joint at bottom and top. Jacket length 250mm. Available in various joint sizes with hose barbs or Ace-Safe connectors.

Bulb type, approximately one bulb per 50 mm, with various joint sizes at bottom and top. Available with hose barbs or Ace-Safe connectors.,/p>

These PYREX® condensers have a high surface area per unit length of the 200mm long jacket with a 19/38 Standard Taper outer joint at the top and a plain drip tip at the bottom. They are primarily used in distillation assemblies Condenser tubulations are approximately 10mm O.D.

With spiral condensing tube having both inlet and outlet connections at top, on same side. With standard taper joints. Length between joints is approximately 80-90 mm longer than the stated coil length.

This PYREX® general purpose condenser can be used for either distillation or extraction. Although the condensing area per unit length of the 200mm long jacket is low, the large capacity water jacket gives efficient cooling. Condenser tubulations are approximately 10mm O.D. The adapter end is…

This PYREX® Friedrichs type condenser affords very efficient operation. The helical inner tube fits closely within the jacket. The vapor tube is sealed to the jacket at an angle of 75° and has an outer 24/40 Standard Taper joint.

Allihn style reflux condenser with a standard taper outer joint at the top and a lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

Suitable for refluxing, extracting and distilling operations With Standard Taper 24/40 drip tip joint at bottom All sizes take stopper size 3

Coil style reflux condenser with tightly wrapped coil providing maximum cooling. Excellent for use with high vapor pressure solvents. Condenser has a top outer standard taper joint and lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

Coil style reflux condenser with a larger diameter jacket and coil, thereby providing maximum cooling capacity, while being shorter in length. Hose connections are on the bottom of the condenser which makes it easier to connect hose/tubing. Connections are GL14 polypropylene hose barbs and screw…

West Condenser Joints: 14/20, 19/22, and 24/40 available Jacket Length: 110, 190, 200, and 300mm available Narrow annular space for fast collant speed thus high cooling efficiency.

Condenser has a large opening at the top for use with dry ice/acetone or liquid nitrogen. Condenser has an outer standard taper joint set at a 75º angle to the condenser body and a lower inner drip tip joint, both being the same size.

Air Cooled Remote Condensers Operate in wide outdoor temperature range from -20ºF to 120ºF. Single or double circuit for single or double unit installations. Heavy gauge galvanized steel for corrosion resistance. Thermally protected fan motors. PVC coated steel fan guards. …

Microscale sublimation adapter with vertically adjustable condenser tube that allows use with 3 mL, 5 mL, and 10 mL microscale vessels. Two-piece adapter features a #7 Ace-Thred at top of vacuum adapter that, with Nylon bushing and O-Ring, forms a compression seal with condenser tube, bottom 14/10…

Condenser has a standard taper outer joint at the top and a lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

Static Waterless Allihn style reflux condenser with a standard taper outer joint at the top and a lower inner drip tip joint and GPI thread on side for filling the condenser with ethylene glycol. Supplied with open top cap and septa for closing off once the condenser is filled. No issues with…

Graham condenser is designed for use in distillation applications. Constructed of borosilicate glass, this condenser has a coiled inner tube to provide additional surface area for highly efficient cooling. Socket is 24/40 with a screw thread connector.

With spiral condensing tube having both inlet and outlet connections at top, on same side. With joints. Length between joints is approximately 80-90 mm longer than the stated coil length. Available with PTFE clad bottom joint.

The Graham Condenser has a coiled inner tube to allow a greater surface for coiling and condensation. Made from heat resistant borosilicate glass. The inner coil is sealed to the outer coil producing a leak proof unit.

Similar to CG-1210 but with the 24/40 outer joint replaced with a serrated hose connection for use with a drying tube. This style condenser is used primarily in Soxhlet extractions or in reflux mode. Hose connections have an O.D. of 10mm at the middle serration.

Two piece cold trap style condenser for use with rotary evaporators. Condenser has an additional 19/38 outer joint sealed onto the condenser to allow continuous feed of volumes exceeding the capacity of the evaporating flask.

Bulb type for use with regular extraction apparatus. Improved design permits greater condensing capacity. Jacket lengths approximately 255mm with one bulb per 50mm.

Liebig condensers are used to cool and condense hot vapor as part of a distilling apparatus. This condenser has a straight inner tube that the condensing vapor passes through, and a larger outer jacket that cooling water passes through. Socket is 24/40

Allihn style reflux condenser with a plain tubulation at the top and a lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

Replacement, borosilicate glass components for R220 rotary evaporators Product offering includes triple coil condensers, Bullfrog condensers and the lower condensate coolers for rotary evaporators. Available in either plain or safety coated versions. Units include black SVL caps & red GL thread…

Jacket has an O.D. of 40mm while coil O.D. is 8mm to provide maximum cooling capacity.

Reflux condenser similar to CG-1213 but with detachable hose connections. Connections are made of polypropylene and provide a safe and easy way of connecting and disconnecting flexible tubing to the condenser. Hose connections have an O.D. of 8mm and an I.D. of 4mm. Supplied complete with two GL-14…

Condenser for use in refluxing from 1 to 20mL of solvent in flasks having a capacity of 5 to 50mL. Minimal surface area provides for better yields while providing adequate cooling. The additional hose connection is provided to allow introduction of an inert gas such as nitrogen. Top hose connection…

Hopkins condenser with tube fitting Dimensions: 50 x 260mm Joints: 24/40 Compatible With: Central collect S-EVAP KD units

Ai SolventVap 2L (evaporating flask capacity) series rotary evaporators come with a modular heating bath, vertical glassware, and digital temperature/rotation control. Its optimized bath volume allows for rapid heat-up times. Thats why our SolventVap evaporators consistently deliver reliable and…

Tightly wound coil provides enough surface area to condense high vapor pressure solvents like hexane. With an internal, coil-type cold finger Standard Taper outer joint at the top, Standard Taper inner drip joint at the bottom 283000 does not have a drip joint Two hose connectors…